A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
The article author is making several great pointers about Installing A Bathtub overall in the content following next.
Installing a tub isn't precisely rocket science, however it does require strong plumbing, woodworking, as well as often, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a reasonably challenging job. If the old tub is easily available, the task can relocate quickly; if you have to open a wall surface to remove the old tub and position the new bath tub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will need a helper to move out the old tub and embeded in the new one. Make sure you have actually certified yourself for the task and fit attempting it. Instead of hiring a contractor to take over a halfway-completed job, it is far better to think about using one prior to you begin. Possibilities are you might require a professional plumber to make tube connections.
This write-up will aid you install a new tub in your bathroom if you have actually currently bought a new bathtub and don't require to transform the setup of your previous water pipelines.
Your tools as well as product list need to make up the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you need to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly problematic because of the limited gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to proceeding to fit the brand-new taps, compare the pipe links on the old taps to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washing machines are in area in between the faucet and also the sink. Safeguard the faucet in place with the supplier provided backnut. As soon as the faucet is firmly in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The previous type should be linked to the tap finishes initially, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Bath tub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are valuable in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto four tiny factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the tub till the spirit level reviews degree.
To mount taps, fit all-time low of the outermost flexible tap connector to the proper supply pipeline by making a compression join; then do the very same for the other faucet.
Activate the water supply and also inspect all joints and new pipework for leakages and also tighten them if needed. Load the tub and additionally check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as securing around the bathtub should wait till the tub has actually been made use of at least when as this will resolve it into its final placement.
Preparing for the Installation
To start with, the supporting framework supplied with the bath must be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to avoid stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last position.
Tiling Around the Bathtub
In the area where the bathroom satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture an inflexible seal, causing the water to pass through the wall between the bath and the tiling, causing problems with wetness as well as possible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components as well as installations. They are marketed in tubes as well as cartridges, as well as are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water before sealing, to allow for the activity experienced when the bathtub is in use. The sealer can break rather early if you do not think about this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily offered on the marketplace. It is recommended to fit the tiles making use of waterproof or waterproof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading up on A Step-by-Step Guide to Installing a Bathtub? Try leaving a remark directly below. We'd be glad to hear your opinion about this posting. Hoping to see you back again before long. Loved our write-up? Please share it. Help somebody else discover it. We value reading our article about Tools You Need to Install a New Bathtub .
Quality fix? Call! Report this page